Payment & Shipping Terms:
|Roll Material:||CR12||The Thickness Of Steel Strip:||0.5-1.5m|
|Milling Speed:||0-90m/min||Mechanical Equipment Site:||45m X4.5m (length X Width)|
|Equipment Motor:||173.2KW||Decoiler:||3 Ton Double Head|
|Pipe O.D:||8-32mm||Transmission:||Gearbox Drive|
|Material:||Hot Or Cold-rolled Steel Strip|
High speed 10-60mm HF Welding Pipe Round Square Tube Making Machine Flying Cut system Watter Cooling
This equipment is specially used for producingΦ8-Φ32mm,δ0.5-1.5 mm High-frequency straight seam welded pipe and corresponding square pipe and special-shaped pipe(δ≤1.2mm). The composition of equipment is from decoiler to fixed length cutting saw. Rolling speed can be adjusted correspondingly within suitable range of pipe diameter and wall thickness.
(1) Hot or cold-rolled steel strip (As per GB700-88 or GB1591-88)
(2)Material: Low-carbon steel, low alloy steelδs≤345Mpa,δb≤610Mpa
(3) The thickness of steel strip: 0.5-1.5mm (As per GB708-88)
(4) The width of steel strip: 25～100mm
(5) I.D. of steel coil: Φ450-Φ550mm
(6) O.D. of steel coil: Φ600～1000mm
(7) Maximum weight coil: ≦800kg
Dimension range of processing steel pipe
(1) O.D: Φ8-Φ32mm
(2) Wall thickness:0.5-1.5mm (square pipe and special-shaped pipeδ≤1.2mm)
(3) Length: 4～8m
1.4 Product (steel pipe) process flow
Raw material (steel coil) → decoiling→ shearing and welding→ material accumulating → non-power leveling →forming milling →high frequency welding →removing burrs outside of weld seam →cooling →sizing →rough straightening → fixed length cutting →finishing pipe
1.5 Milling speed: 20-100m/min
1.6 High-frequency equipment power: 100 KW
1.7 Suggested necessary accessories prepared the Buyer (for reference only)
(1)Mechanical equipment site: 30m X4m (length X width)
(2)Electrical equipment site: 5m X 3m (length X width)
(3)Machine unit foundation base (See supplier’s base drawing)
(4)Two sets of 3-ton overhead crane
a. Equipment motor: 45KW+2.2KW+7.5KW+3KW=57.7KW
b. High-frequency motor: 100 KW
(6) Blades for tracking saw, specification as per instruction book .The quantity is decided by the customer.
(7) Magnetic bar for welding pipe, purchase as per pipe making size.
(8) one set of Φ2”, 6m high-pressure pumps for high frequency pipe welding machine cooling.
(9) One set of cooling water pool for pipe-welding machine and high frequency electric equipment, volume 20m3with water pipe, water pressure meter and valve. (Quantity and sizes shall be decided on site, then purchase outside)
(10) Machine unit electric circuit. Before assembling, circuit must reach the electric cabinet of high-frequency room. Electric connection for high-frequency room to overall control table and button station. (Quantity and sizes shall be decided on site, then purchase outside)
(11) One high-frequency room for machine unit. Adopting ground or attic according to customer’s layout.
(12) Air compressor: one set (market purchase)
(13) Lifting equipment and tooling for installing machine,(crane, steel wire rope, etc) maximum weight of one part is 8tons.
Introduction of Main Components
Structure type: Double-side, 360°Rotation, manual expanding, which insures steel coil feed alternatively and go into accumulator freely.
2. Vertical Accumulator
3. Forming welding and sizing device
4. Computer saw
5. the out table